Maintaining the quality and sanitation of the water in your unit is critical for ensuring user safety, optimizing performance, and preserving the longevity of the system components. Adherence to a consistent maintenance protocol is essential to preve

Maintaining the quality and sanitation of the water in your unit is critical for ensuring user safety, optimizing performance, and preserving the longevity of the system components. Adherence to a consistent maintenance protocol is essential to prevent the accumulation of organic compounds, contaminants, and microbial growth. This section outlines the required procedures for water replacement and best practices for proactive water care. <h4 id="a-minimum-water-replacement-schedule">A. Minimum Water Replacement Schedule</h4> This schedule represents the minimum frequency required for typical residential use. High-usage environments will require an accelerated maintenance schedule.<ol start="1"><li>Weekly Partial Water Change:It is mandatory to replace 25% to 50% of the total water volume on a weekly basis. This procedure serves to dilute the concentration of total dissolved solids (TDS), organic matter, and other accumulated contaminants, thereby reducing the sanitation load on the filtration and chiller system.</li><li>Periodic Full Water Change:A complete drain, interior surface cleaning, and full refill must be conducted every four (4) to six (6) weeks. This process fully resets the water&#x2019;s chemical balance and provides an opportunity to thoroughly sanitize the tub&#x2019;s interior, which is crucial for preventing biofilm development.</li><li>High-Usage Addendum:For units subjected to high-usage conditions, such as in commercial, athletic, or multi-user daily environments, the frequency of both partial and full water changes must be significantly increased. Under such conditions, daily water quality assessment is strongly recommended.</li></ol> <h4 id="b-water-quality-indicators-demanding-immediate-action">B. Water Quality Indicators Demanding Immediate Action</h4> The following sensory indicators supersede the standard maintenance schedule. If any of these conditions are observed, a full water change must be performed immediately to restore hygienic conditions.<ul><li>Visual Turbidity (Cloudiness): The water loses its clarity and appears hazy, milky, or cloudy. This indicates a high concentration of suspended microscopic particles, which may include organic waste, skin cells, or burgeoning microbial colonies.</li><li>Odor Generation: The water emits any abnormal, musty, or unpleasant odor. Odors are a primary indicator of bacterial or fungal activity and the chemical breakdown of contaminants.</li><li>Biofilm Formation: The interior surfaces of the tub feel slippery or slimy to the touch. This tactile sign indicates the presence of a biofilm&#x2014;a complex colony of microorganisms that adheres to surfaces and can harbor pathogens.</li></ul> <h4 id="c-best-practices-for-maintaining-water-purity">C. Best Practices for Maintaining Water Purity</h4> Proactive measures are the most effective way to prolong the interval between water changes and ensure a consistently clean environment.<ol start="1"><li>Utilize the Insulated Cover: The tub cover must be kept on and securely fastened at all times when not in use. This practice is critical for preventing airborne contaminants (e.g., dust, pollen, debris) from entering the water, reducing water evaporation, and maintaining thermal efficiency.</li><li>Enforce Pre-Use Hygiene: Users must shower or rinse off immediately before entering the tub. This removes sweat, natural body oils, and residual personal care products such as lotions, cosmetics, deodorants, and creams. These substances introduce a high organic load that can overwhelm the sanitation system, serve as nutrients for microbial growth, cause foaming, and reduce overall water quality.</li></ol>

Water Care and Maintenance Protocol

Proper care of your Primal Plunge Air Tub is essential for ensuring optimal performance, user safety, and long-lasting water quality. Please follow the guidelines below for routine upkeep, organized by frequency. To maintain water freshness and dilut

<h3 id="isPasted">Primal Plunge Air Tub: Care and Maintenance Guide</h3> Proper care of your Primal Plunge Air Tub is essential for ensuring optimal performance, user safety, and long-lasting water quality. Please follow the guidelines below for routine upkeep, organized by frequency. <h4 id="1-weekly-water-refresh">1. Weekly Water Refresh</h4> To maintain water freshness and dilute the concentration of contaminants, perform a partial water change once per week.<ul><li>Procedure: Drain approximately 25% to 50% of the water from the tub and refill it with fresh, cold water.</li><li>Optional Water Treatment: As an alternative to weekly water changes, you may use the official Primal Plunge Water Treatment Kit (sold separately). When our water cleanser is used according to the directions, the interval between full water changes can typically be extended to once per month.</li></ul> <h4 id="2-monthly-deep-cleaning--filter-service">2. Monthly Deep Cleaning &amp; Filter Service</h4> Once per month, perform a comprehensive deep cleaning of the tub and the filter to reset the environment and remove any accumulated buildup.<ol start="1"><li>Drain the Tub: Completely empty all water from the tub.</li><li>Clean the Filter: While the tub is draining, remove the filter cartridge from the IceFlow chiller. The filter can be washed by hand with warm water and mild dish soap, or placed in a dishwasher for a cleaning cycle.</li><li>Clean the Tub Interior: Using a soft sponge or cloth and a mild dish soap, thoroughly wipe down all interior surfaces. Pay close attention to corners, seams, and crevices to ensure they are free of any residue.</li><li>Rinse Thoroughly: Once the tub is clean, rinse the interior completely with fresh water to remove all soap residue.</li><li>Refill: Refill the tub to the appropriate level with fresh, cold water.</li></ol>IMPORTANT: To protect the integrity of the tub&apos;s material, do not use harsh chemicals, bleach, or abrasive scrubbers/brushes. Use of such agents can cause permanent damage, shorten the tub&#x2019;s lifespan, and may void the product warranty. <h4 id="3-scheduled-filter-replacement">3. Scheduled Filter Replacement</h4> To maintain maximum filtration efficiency and ensure optimal water hygiene, the filter cartridge must be replaced periodically.<ul><li>Replacement Interval: Replace the filter every four (4) to six (6) months, or more frequently if the tub experiences heavy use.</li></ul>

Cleaning Your Primal Plunge Tub

Proper site selection and setup are critical for the safe, efficient, and long-term operation of your Primal Plunge Air Tub and IceFlow Chiller. Failure to adhere to the following requirements can result in product damage, suboptimal performance, or

Proper site selection and setup are critical for the safe, efficient, and long-term operation of your Primal Plunge Air Tub and IceFlow Chiller. Failure to adhere to the following requirements can result in product damage, suboptimal performance, or potential safety hazards. Please review all guidelines carefully before beginning installation. <h4 id="1-foundation-and-structural-support">1. Foundation and Structural Support</h4> The selected site must provide a sturdy, flat, and perfectly level surface. The foundation must be engineered to support the total operational weight of the tub, which includes the water and occupants (consult the product specifications for exact weight).<ul><li>Recommended Surfaces: Concrete pads, reinforced decks, structural flooring, or solid, compacted ground.</li><li>Unsuitable Surfaces: Avoid placing the unit on soft ground, uneven lawns, or any surface that is not level. An unlevel foundation can cause structural stress on the tub, leading to material failure and creating an unstable, unsafe condition.</li></ul> <h4 id="2-environmental-placement-indoor-vs-outdoor-use">2. Environmental Placement: Indoor vs. Outdoor Use</h4> Your tub is designed for both indoor and outdoor installation. Please follow the specific recommendations for your chosen environment.<ul><li>2.1 Outdoor Installation:<ul><li>Shade and Protection: Choose a location that offers protection from prolonged, direct sunlight. This minimizes potential UV degradation of the tub materials and reduces solar heat gain, allowing the chiller to operate more efficiently.</li><li>Debris: Position the tub away from trees or shrubs that could drop leaves, pollen, or other debris into the water.</li><li>Ground Surface: Ensure the ground is free of sharp objects, rocks, or roots that could puncture or damage the base of the tub.</li></ul></li><li>2.2 Indoor Installation:<ul><li>Ventilation: The room must have adequate ventilation (e.g., an exhaust fan or an operable window) to manage humidity and prevent the buildup of excess moisture, which can lead to mold or mildew.</li><li>Drainage and Flooring: The floor surface should be water-resistant. Proximity to a floor drain is highly recommended to simplify the draining process. Be prepared for minor splashing and ensure the surrounding area can tolerate water exposure.</li></ul></li></ul> <h4 id="3-utility-and-service-access">3. Utility and Service Access</h4> For ease of use and maintenance, the location must provide convenient access to necessary utilities.<ul><li>Power Source: The IceFlow chiller must be plugged into a dedicated, properly grounded GFCI (Ground Fault Circuit Interrupter) protected electrical outlet. This is a mandatory safety requirement for any electrical appliance used with water.</li><li>Water Source: The site should be within reach of a water source, such as a garden hose, for efficient filling and periodic water changes.</li></ul> <h4 id="4-iceflow-chiller-ventilation-requirements">4. IceFlow Chiller Ventilation Requirements</h4> To ensure optimal cooling performance and prevent overheating of its components, the IceFlow chiller requires unrestricted airflow.<ul><li>Clearance: You must maintain a minimum of 12 inches (30 cm) of clear, unobstructed space around all sides of the chiller unit.</li><li>Restrictions: Do not block the ventilation ports or operate the chiller in a tight, enclosed cabinet or closet. Impeding airflow will significantly reduce cooling efficiency and can lead to component failure.</li></ul>

Where Do I Put My Primal Plunge

Need more help? Reach out to us for additional support or returns & warranty support.

Want to reach out to our mobile support team? Call today for any additional guidance or support!

goprimalhealth

Complete cold plunge maintenance guide. Learn water care, filter cleaning, chiller maintenance, and daily upkeep to keep your system running perfectly